MICROCONTROLLER BASED SMOKE DETECTOR
ABSTRACT
The microcontroller smoke detector is a system designed to provide security level in areas that requires high accuracy of precaution...
DESIGN AND CONSTRUCTION OF A 60 WATTS POWER AMPLIFIER
INTRODUCTION
An audio AMP is basically a system which is used as a means of increasing the level of sound or audio signals for maximum...
ABSTRACT
The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to...
ABSTRACT
Uninterruptible power supplies (UPS) are used to provide power when regular utility power is unavailable. Although they are commonly used for providing power in remote locations or emergencies, this is not because they are the same as auxiliary power units, emergency...
COMPUTER BASED ANALYSIS OF ELECTRICAL POWER SYSTEM FOR THE PURPOSE OF STABILITY STUDIES
ABSTRACT
This report is on stability study in electrical power system. The ability of an electric power system to reestablish the initial state (or one practically identical) after any disturbance...
DESIGN AND CONSTRUCTION OF AN AUTOMATIC SINGLE PHASE CHANGEOVER SWITCH
ABSTRACT
The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the...
MICROCONTROLLER BASED MULTIPURPOSE SECURITY DEVICE WITH DIRECTION
ABSTRACT
This project outlines the design and implementation of microcontroller based multipurpose security device with direction which can be used in the military to provide utmost security/safety in the cantonment....
DESIGN AND CONSTRUCTION OF 1.5 KVA INVERTER
CHAPTER ONE
1.1. INTRODUCTION
Currently almost all the inverters available in the market use the PWM (Pulse Width Modulation) technology. PWM based inverters are superior in many ways compared to the inverters based on traditional...
DESIGNING AND CONSTRUCTING OF AN AUTOMATED LIGHT SYSTEM USING PHOTO-SENSITIVE SWITCH.
CHAPTER ONE
1.0. INTRODUCTION
1.1. GENERAL DESCRIPTION OF THE PROJECT
Industrial electronics has turned the whole world into a global village. One of the most indispensable aspects of these...
DESIGN AND CONSTRUCTION OF AUTOMATIC CHANGE OVER SWITCH WITH INDICATOR
ABSTRACT
This project work deals on the design and construction of an automatic power changeover that will change/transfer control from MAINS to Gen set and can switch ON/OFF the Gen automatically. The system integrates...
DESIGN AND IMPLEMENTATION OF
AUTOMATIC THREE PHASE SELECTOR SWITCH
v
ABSTRACT
Automatic 3 phase selector switch is a replacement of 3 phase manual change over cut fuse from one cut out to another. Automation 3 phase selector switch has an input of 3 phases from...
ABSTRACT
Availability of electric power has been the most powerful vehicle for facilitating economic, industrial and social developments of any nation. Electric power is transmitted by means of transmission lines which deliver bulk power from generating stations to load centres and...
AN IMPROVED FAULT LOCATION ON POWER SYSTEM TRANSIMMISION LINES USING FUZZY LOGIC APPROACH
ABSTRACT
The problem of Electricity are enormous and can never be treated completely until the fault department (maintenance) are improved upon for urgent and rapid response to line faults.
The...
DESIGN AND CONSTRUCTION OF MICRO-CONTROLLER BASED MULTI-PURPOSE SECURITY SYSTEM WITH DIRECTIONS
ABSTRACT
This project outlines the design and construction of micro-controller based multi-purpose security system with directions which can be used in the military to provide utmost...
DESIGN AND IMPLEMENTATION OF AUTOMATIC 3 – PHASE CHANGE – OVER WITH GEN SET SWITCHING CHAPTER ONE
INTRODUCTION
The evolutionary trend in industrial electronics and automation has engulfed all parts of the world and proved more challenging to as third world like Nigeria. Regarding...
DESIGN AND CONSTRUCTION OF A CAR TRACKER SYSTEM
ABSTRACT
The purpose of this project is to design and construct a car tracker system with code using GSM. A good car attracts everyone including thieves. When it comes to the safety of cars, car owners should be very careful. These days, the...
DESIGN AND CONSTRUCT AN AUTOMATIC CHANGE-OVER SWITCH WITH INDICATOR THAT WILL SWITCH LOAD FROM THE MAINS POWER SUPPLY (PHCN) POWER SUPPLY (GENERATOR) WITH SIMPLICITY.
CHAPTER ONE
INTRODUCTION
Industrial automation and control has contributed immensely to the high rate of the world’s...
DESIGN AND CONSTRUCTION OF AUTOMATIC THREE PHASE SELECTOR SYSTEM
ABSTRACT
Automatic 3 phase selector switch is a replacement of 3 phase manual change over cut fuse from one cut out to another. Automation 3 phase selector switch has an input of 3 phases from PHCN but has one output that...
ABSTRACT:
This project deals with the design and implementation of a radio controlled car lock with 5-minutes ignition deactivation facility capable of locking a vehicle using a remote control from a distance. The system is designed in two functional units; the transmitter which is an RF...