Design And Construction Of Control System For Direct-on-line Starting Of Induction Machine
Electrical/electronic Engineering Project Topics
Get the Complete Project Materials Now! ยป
DESIGN AND CONSTRUCTION OF CONTROL SYSTEM FOR DIRECT-ON-LINE STARTING OF INDUCTION MACHINE
ABSTRACT
This project describes the methodical approach to the design and construction of control system for direct-on-line starting of induction machine. The procedures developed covers the construction of D.O.L stated for lower horse power motors. The prototype of this direct-on-Line starting of induction machine has been implemented following the methodical approach outlined in this project and its operational test and result are quite satisfactory. Adequate care has been taken in the design and construction of this project to ensure reliability. Therefore, the project is aimed at controlling the operation of single phase and three phase motors in industrial drive, companies, homes, laboratories and hospitals thereby reducing economic waste.
TABLE OF CONTENTS
Title page - - - - - - - - i
Certification - - - - - - - - ii
Dedication - - - - - - - - iii
Acknowledgement - - - - - - - iv
Abstract - - - - - - - - - v
Table of contents - - - - - - - vi
CHAPTER ONE
1.0 Introduction -- - - - - - - 1
1.1 Aims and objective of the study - - - 3
1.2 The scope of the study - - - - - 4
1.3 The limitation of the study - - - - 5
1.4 Definition of terms - - - - - - 6
CHAPTER TWO
2.0 Literature review - - - - - - 8
2.1 Contactor - - - - - - - 11
2.2 Circuit breakers - - - - - - 14
2.3 Overload relays - - - - - - 14
2.4 Push button - - - - - - - 15
2.5 Auto-transfer starting - - - - - 16
2.6 Primary resistor starting - - - - 17
2.7 Star-Delta starting - - - - - - 18
2.8 Star-Delta Starting - - - - - 18
2.9 Factors that determine the use of the method of starting of induction machine by D.O.L Are - 19
2.10 Factors taken into consideration for component values and sizes - - - - - - 20
2.11 Application of direct-on-line starting of induction 22
CHAPTER THREE
3.0 Design methodology - - - - - 24
3.1 Block diagram - - - - - - 25
3.11 Input stage - - - - - - - 26
3.12 Control stage - - - - - - - 30
3.13 Output stage - - - - - - - 30
3.14 Advantage of block diagram over circuit diagram 31
3.2 The circuit Diagram - - - - - 32
3.21 Mode of operation - - - - - - 33
3.22 Production of starting torge - - - - 35
3.23 Material determination of starting and starting torge of induction machine - - - - 38
3.3 Component parts - - - - - - 39
3.31 Circuit Breakers - - - - - - 39
3.32 Overload relay - - - - - - 41
3.33 Direct-on-line contactor - - - - - 42
3.34 Push buttons - - - - - - - 43
3.35 Indicator light lamp - - - - - 45
3.36 Connecting leads - - - - - - 45
3.37 Connecting leads - - - - - - 45
CHAPTER FOUR
4.0 Construction, testing and packaging - 47
4.1 Mounting of component - - - - - 47
4.2 Testing - - - - - - - - 49
4.3 Component lists - - - - - - 50
4.4 Assembly and packaging - - - - 51
CHAPTER FIVE
5.0 Bill of engineering management and evaluation (BEME) - - - - - - - - 54
5.1 Table 5.1 Bill of engineering measurement and evaluation as at Date: 17th October, 2011.- 54
5.2 Remark - - - - - - -- - 55
CHAPTER SIX
6.0 Summary - - - - - - - 57
6.1 Recommendation - - - - - - 59
6.2 Conclusion - - - - - - - 60
6.3 Reference - - - - - - - 62
6.4 Appendices - - - - - - - 63
CHAPTER ONE
1.0 INTRODUCTION
Design and construction of control system for direct-on-line starting of induction machine: This is a control system that can control a single phase (1Ø) motors and three phase (3Ø) by making use of the components such as contactors, over current relay, start button, stop button etc. the contactors provides switching devices while over current relay is positioned to render protection to the machines in case of over current surge, the start and stop buttons called push buttons are used to start and stop the control contactor system. Again, there are pivot or indicator lamps which are controlled by normally open and normally closed of the auxiliary contacts incorporated to indicate when there is voltage supply to the three phase (3Ø) or single phase (1Ø) or both phases. However, the whole control system is controlled by mechanically pressing the push button ON and OFF when the circuit breaker has been switched ON.
The energy needed for the operation of the control system is three phase and one neutral through the input to produce single and three phase at the output terminal.
Finally the mode of operation is shown on the circuit diagram of the control system.
Organizational report: In chapter, 1 discussed about the background, aim, scope and limitation of the project.
In chapter two, literature review of the project is discussed and elaborated.
In chapter three, the design methodology (design Analysis, investigation and data) is discussed.
In chapter four, construction, testing and packaging is described.
In chapter five, Bill of Engineering measurement and evaluation (BEME) are stated.
In chapter six, this is where the summary, conclusion and recommendation, reference and Appendices are stated.
1.1 AIMS/OBJECTIVE OF THE STUDY
The aims/object of embarking on the project are:
1) To produce a system that will protect electric motor.
2) To design a control system that will start induction machines without causing damage to the equipment.
Be the First to Share On Social
PROJECT DETAILS |
|
| Project ID | EL1708 |
|
RELATED TOPICS
Role Of Insurance Industry In Management Of Environmental Risk Design And Construction Of A 3 Way Inter-communication System. The Design And Construction Of An Uninterrupted Power System (ups) Design And Construction Of An Alternative Household Power Generating System Design And Implementation Of Intruder Detector Alarm System With Location.
